12/30/2023 0 Comments Z6 nef dxo photolabThe 24-120/f4 is also quite sharp, but Lightroom doesn’t remove the CA (at least so it seems). Also, the image quality is outstanding (unlike the Canon R5 / RF 15-35/f2.8 combo I used before), with perfect sharpness and no CA. The 12-24 is listed in LR and I can turn the profiles on and off. Thanks for pointing this out! I recently purchased a Nikon Z7 II and the 12-24/f2.8 as well as the 24-120/f4 Z lenses. Meanwhile, if you happen to have a Z6 II / Z7 II and any of the lenses I haven’t been able to test, I’d appreciate some info in the comments section so I can add to the lists at the start of the article! We’ll be updating our Nikon Z lens reviews over the coming days to reflect the different behavior with the Nikon Z6 II and Z7 II. Why not just apply these corrections automatically (including vignetting – not tied to the level selected in camera) and then allow us to turn them off if we want? At this point, I don’t know if it’s Adobe or Nikon who is at fault, but the situation has gotten very strange. But the whole decision about non-removable profiles isn’t something I can get behind. I understand why Lightroom would have some built-in corrections that are automatically applied to certain Nikon lenses, especially a lens like the 14-30mm f/4 that has almost fisheye levels of distortion. Uncorrected vignetting on the Nikon Z 24-70mm f/4, shot in raw with in-camera vignetting turned off Some documentation from Adobe or Nikon on how this works would be nice. The vignetting weirdness is true regardless of the Nikon Z camera you’re using, as best as I can tell. If the effect ends up looking too strong (a definite possibility), you can add back your desired level of vignetting in the Effects panel. That signals Lightroom to apply full vignetting corrections as part of the built-in lens profile. So, my recommendation for Nikon Z shooters is to keep the vignetting correction in-camera turned to High, even if you’re shooting. Of course, the Effects tab further down in Lightroom has its own vignetting tool, but it tends to work better for adding vignetting rather than precisely removing it. Puzzlingly, it takes your in-camera selection as the un-erring truth and applies it to your photos, without allowing you to change this value within the Lens Corrections tab. Rather than the built-in lens profile automatically applying a certain amount of vignetting correction, Lightroom actually reads how much in-camera vignetting correction you selected. But something of further interest – not totally new information but something that I don’t see mentioned that often – is that Lightroom is taking a strange approach to the vignetting correction with Nikon Z lenses. So, that’s how the distortion profiles work now. Lightroom has non-removable lens profiles with most Nikon Z cameras and lenses. With other Nikon Z cameras, the distortion profiles are still automatically applied, no matter what lens you use. With the f/2.8 zooms as well as most or possibly all Nikon Z prime lenses, you can now turn off the distortion profiles in Lightroom – but only if you’re using the Z6 II or Z7 II. I no longer have most of the other Nikon Z lenses and can’t confirm which category everything falls under (crowdsourced tests would be appreciated!) but the general idea is this. Whereas with at least the following lenses, it still applies, no matter what camera you’re using: The short version of the story is that with the Nikon Z6 II and Nikon Z7 II specifically, the distortion profiles can now be turned on and off for at least the following lenses: But with some of the newer Z cameras and certain lenses, the issue (mostly) no longer applies. I’ve consistently been annoyed by the non-removable lens profiles in Lightroom when using Nikon Z cameras.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |